Potensi Karton Bekas Minuman sebagai Komposit... : Andri Taufck Rizaluddin, dkk. 21 Potensi Karton Bekas Minuman sebagai Komposit PolyAl-fber Andri Taufck Rizaluddin * , Ike Rostika, Reza Bastari Imran Wattimena Balai Besar Pulp dan Kertas, Jl. Raya Dayeuhkolot No. 132 Bandung, Indonesia Diterima : 5 April 2020, Revisi akhir : 30 Mei 2020, Disetujui terbit : 30 Juni 2020 Potential of Used Beverages Cartons for PolyAl-fber Composite Abstract Various recycling processes have been developed to overcome the problem of Used Beverage Carton (UBC) waste. Research was conducted to determine the potential utilization of UBC as a material for more waterproof composite and compared it to similar products. The composites were made using hot press machine at temperature of 165 o C and pressure of 25-30 kg/cm 2 for 10 minutes with 5% - 30% fber content. The PolyAl-fber composite obtained had bending strength of 12.78 MPa, bending modulus of 11.60 GPa, fammability of 3 cm/min, water absorption of 2.1-14.1%, moisture content of 0.9-1.9%, and density of 0.68-0.94 g/cm 3 , at thickness of 2.5-3.5 mm. The PolyAl-fber composite could meet the requirements for fberboard, particleboard, or plastic wood composite standards without extra additives or treatment to the raw materials, indicating that it could be used for similar purposes. The PolyAl-fber composites may able to produce a better quality of composite boards, due to their fexible, waterproof, and fre-resistant characteristics compared to similar products made from wood or biomass. Keywords: UBC, PolyAl-fber composite, water absorption, bending strength Abstrak Dalam rangka penanggulangan limbah Karton Bekas Minuman (KBM), telah dikembangkan proses daur ulang untuk mengembalikannya menjadi bahan baku. Tujuan penelitian ini adalah untuk mengetahui potensi pemanfaatan KBM sebagai bahan baku komposit yang lebih tahan air, dan membandingkannya dengan spesifkasi teknis produk sejenis. Pembuatan komposit dilakukan dengan pemanasan menggunakan alat hot press pada suhu 165 o C dan tekanan 25-30 kg/cm 2 selama 10 menit. Produk komposit yang diperoleh memiliki nilai bending strength 12,78 MPa, bending modulus 11,60 GPa, fammability 3 cm/menit, daya serap air 2,1-14,1%, kadar air 0,9-1,9%, dan rapat massa 0,68-0,94 g/cm 3 , pada ketebalan 2,5-3,5 mm. Komposit PolyAl-fber dapat memenuhi persyaratan standar papan serat, papan partikel maupun komposit kayu plastik tanpa penambahan bahan maupun proses lain, yang mengindikasikan komposit PolyAl-fber memiliki potensi untuk digunakan dalam berbagai keperluan sejenis. Komposit PolyAl-fber akan dapat menghasilkan papan komposit dengan kualitas lebih baik, karena lebih feksibel, lebih tahan air, dan lebih tahan api bila dibandingkan dengan produk lain yang terbuat dari bahan baku kayu atau biomassa. Kata kunci : KBM, komposit PolyAl-fber, daya serap air, bending strength Jurnal Selulosa Vol. 10 No. 1 Juni 2020 Hal. 21 - 34 JURNAL SELULOSA e-ISSN: 2527 - 6662 p-ISSN: 2088 - 7000 * Alamat korespondensi : E-mail: andritr3@gmail.com © 2019 - Jurnal Selulosa all rights reserved. Open access under CC BY-NC-SA license. (http://creativecommons.org/licenses/by-nc-sa/4.0/) DOI: http://dx.doi.org/10.25269/jsel.v10i01.293