ISSN: 2277-9655 [Jojowar* et al., 6(10): October, 2017] Impact Factor: 4.116 IC™ Value: 3.00 CODEN: IJESS7 http: // www.ijesrt.com© International Journal of Engineering Sciences & Research Technology [134] IJESRT INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY ANALYSIS OF EFFECTS OF HEAT TREATMENT PROCEDURES ON CHARACTERISTICS OF IRON Romiyo Mclin Jojowar *1 , Dr Lokendra Pal Singh 2 & Rajneesh Yadav 3 *1 M.Tech Scholar, Dept. of Mechanical Engineering, SHUATS, Allahabad, U.P., India 2 Asst. Professor, Dept. of Mechanical Engineering, SHUATS Allahabad, U.P., India 3 M.Tech Scholar, Dept. of Mechanical Engineering, SHUATS, Allahabad, U.P., India DOI: 10.5281/zenodo.1002673 ABSTRACT The initial study was conducted on unalloyed ductile iron castings. The effect of austempering time was examined by varying austempering time in the range of 30 minutes to 90 minutes, while keeping austenitization temperature and austempering temperature constant. It was found that with the increase of austempering time, the tensile strength increased significantly. However, at 90 minutes the tensile strength decreased. The optimum temperature was found to be 60 minutes. The second variable was the effect of austenitization temperature on ductile iron. Based on the result of the first experiment, the austempering was carried out for 90 minutes. The austempering temperatures were kept at 270ºC and 370ºC. The austenitization temperature was varied from 850ºC to 925ºC. The study revealed that tensile strength increased at 900ºC but it decreased at 925ºC. The third major variable involving the effect of alloying additions on ductile iron, was studied by adding copper with three different values i.e. 0.5 wt. %, 1.0 wt. % and 1.5 wt. %. The fourth melt was without the addition of copper. It was found that with the increase of copper the tensile strength continued to increase up to 1.5 wt. %. The second alloying addition was nickel. One melt was made without nickel while the remaining three melts were made with the addition of 1.0 wt. %, 2.0 wt. % and 3.0% nickel. The tensile strength increased correspondingly with the increase in the addition of nickel to 3.0 wt. %. The effect of a combination of copper and nickel on ductile iron was also examined. The effect of the last alloying element which was studied was lanthanum. Four melts were made for this study. The first melt was without the addition of lanthanum while the remaining three had 0.006 wt.%, 0.02 wt.% and 0.03 wt.% lanthanum. The results indicated that the tensile strength increased with the increase of lanthanum content with and without austempering. Furthermore, the highest nodule count was obtained with 0.03 wt. % lanthanum while the nodularity remained almost unchanged. Thus, it was observed that the addition of alloying elements results in an increase of tensile strength. The optimum austempering time was 90 minutes and the optimum austenitizing temperature was found to be 900ºC. KEYWORDS: Austempering, austenitizing temperature, tensile strength and nodularity. I. INTRODUCTION The increasing interest in energy saving has led to the development of lightweight materials to reduce the weight of existing materials without compromising their properties. In the automotive industries, attempts have been made to replace cast iron and steel components with aluminum and austempered ductile iron. Austempered ductile iron (ADI) is a ductile iron that has undergone a special isothermal heat treatment called austempering. Unlike conventional “as-cast” irons, its properties are achieved by specific heat treatment. Therefore, the only prerequisite for good ADI is a good quality ductile iron. ADI offers superior combination of properties because it can be cast, like any other member of the ductile iron family. It offers all production advantages of conventional ductile iron castings. Subsequently it is subjected to the austempering process to produce mechanical properties that are superior to conventional ductile iron, many cast and forged steels.