Majid S Al Ruqeishi*, Younis Al Salmi and Tariq Mohiuddin Department of Physics, Sultan Qaboos University, Oman *Corresponding author: Majid S Al Ruqeishi, Department of Physics, College of Science, Sultan Qaboos University, Oman, Email: Submission: April 26, 2018; Published: May 08, 2018 Nanoparticles as Drilling Fluids Rheological Properties Modifiers Introduction The drilling operation is the first stage in tapping underground oil, gas, and water. The proper development of this operation plays a major role in increasing productivity. Drilling fluid, mud, is pivotal in achieving this objective. Drilling fluids can be of many types; water-based, oil-based, synthetic-based fluids, and pneumatic or air fluids are a few commonly used in drilling. Water-based fluids are the most common. They are utilized to drill approximately 80% of all wells and are more economical compared to oil or synthetic-based fluids [1,2]. Drilling fluids have various functions during the drilling operation. These including: transport of cuttings to the surface, maintaining the wellbore pressure and stability, lubrication and cooling of the drill bit and isolation of formation fluids and gases by forming a filter cake around the borehole. Most troublesome drilling issues are directly or indirectly triggered by fluid related problems and the most recurring are loss of drilling fluid and wellbore instability. Drilling fluid circulation loss, which is defined as the gradual or accidental loss of drilling fluid to formation voids is one of the most well-known drilling problems. This leads to higher costs due to increase in the time required to reach the target depth, loss of pressure control, increased safety concerns on the rigs, contamination of waterbeds as well as several other consequences [3]. A large effort has been put into the development of new Lost Circulation Materials (LCMs) and technologies to plug the openings in the wellbores, with various levels of success. The key to experience a “fluid loss free” drilling operation lies within the ability to build a firm and high strength plug over the fractures and other types of “thief zones” to maintain the fluid level in the borehole [4,5]. LCMs with diameters in the range of 0.1-100μm could play an important role when the fluid loss occurs in 0.1μm- l mm porous formations. However, the size of pore openings in formations such as shale,lead to lossesin the range of 10 nm to 0.1μm and here LCM’s are not very effective [6]. Nanoparticles can be described as solid particles or particulate dispersion in the size range of 1 to 100nm. Amanullah & Al Tahini [7] define nano- fluid as the fluid used in oil and gas drilling and exploitation which contains at least one nanoscale additive. As shale formations have small pores, the prevention of the fluid from penetrating into this formation is the main application of the nanoparticles in the drilling fluids. The presence of nanoparticles contributes to the sealing of the micro cracks in the shale and hence the filter cake becomes dense, thinner and impermeable. Forming such a filter cake reduces the fluid loss and stabilizes the well [8-11]. Salem Ragab & Noah [12] used nano-sized silica drilling fluids for the reduction of formation damage and fluid loss, thereby providing a smooth drilling operation. William et al. [13] investigated the effect of CuO and ZnO nanofluids combined with xan than gum on the thermal, electrical and rheological properties of the water-based drilling fluids. Results showed that the increased concentration of nanoparticles enhances electrical and thermal properties and improves rheological stability when using the nanofluid-enhanced water- based drilling mud. Moreover, these results are the same as those Research Article Progress in Petrochemical Science C CRIMSON PUBLISHERS Wings to the Research 1/7 Copyright © All rights are reserved by Majid S Al Ruqeishi. Volume 1 - Issue - 5 Abstract Drilling for water, oil, or even gas using water-based drilling fluids faces major challenges. These are mainly related to drilling fluid leakage into the surrounding formation, water loss into fractures, and the reduction of fluid density or/and viscosity through the drilling circulation process. Nano- additives with high surface to volume ratio of carbon nanoparticles (CNP), ~50nm, and ZnO nanowires provide significant control of drilling fluid rheological properties. CNP additives were found to maintain the homogeneity of the drilling fluid components for a longer time and delay fluid sagging effect. Drilling fluid densities were enhanced by a factor of 4-10% after addition of CNP or ZnO nanowires to the untreated drilling fluid by 1-3 wt. %. Progressively, when 1, 2 and 3g of CNP was added to the drilling fluid, the resultant filtrate water volume was reduced by 7, 4.8 and 4mL respectively. The maximum water loss reduction measured was about 50% of the total fluid loss. Additionally, about a 24% increase in the drilling fluid viscosity was achieved when 2g of ZnO nanowires were added.