А. Н. Рыков, Б. В. Артемьев «Опыт практического определения погрешности суммарной площади дефектов...» 18 Контроль. Диагностика № 1, 2018 УДК УДК 620.179.16 DOI: 10.14489/td.2018.01.pp.018-024 ОПЫТ ПРАКТИЧЕСКОГО ОПРЕДЕЛЕНИЯ ПОГРЕШНОСТИ СУММАРНОЙ ПЛОЩАДИ ДЕФЕКТОВ ПРИ АВТОМАТИЗИРОВАННОМ УЛЬТРАЗВУКОВОМ КОНТРОЛЕ ИЗДЕЛИЙ ИЗ ПОЛИМЕРНЫХ КОМПОЗИЦИОННЫХ МАТЕРИАЛОВ А. Н. Рыков АО «Центральный научно- исследовательский инсти- тут специального машино- строения» (АО «ЦНИИСМ»), г. Хотьково, Московская обл., Россия Е-mail: rykovan@rambler.ru, Б. В. Артемьев, д-р техн. наук (ЗАО «НИИИН «МНПО «Спектр» МГТУ им. Н. Э. Баумана, Москва, Россия), Е-mail: boris@artemiev.su Рассмотрены вопросы точности определения площадей дефектов при бесконтактном ультразвуковом автоматизированном неразрушающем кон- троле цилиндрических изделий из полимерных композиционных материа- лов (ПКМ), проводимого по типовой методике на АО «ЦНИИСМ». Выпол- нен теоретический расчет зависимости относительной погрешности опреде- ления площадей дефектов от их площади для различных значений парамет- ров сканирования. Приведены результаты экспериментальных исследова- ний, качественно подтверждающих теоретические положения. Количест- венная оценка погрешности суммарной площади дефектов показала, что результирующая величина находится в пределах 20 % и зависит от размеров дефектов, выявленных при контроле. Ключевые слова: бесконтактный ультразвуковой контроль, погреш- ность сканирования, площадь дефектов. A. N. Rykov (Central Research Institute for Special Machinery, JSC (CRISM JSC), Khotkovo, Moscow Region, Russia), B. V. Artemyev (NIIIN “MNPO “SPEKTR”, JSC, Bauman MGTU, Moscow, Russia) EXPERIENCE OF PRACTICAL DETERMINATION OF TOTAL DEFECT AREA ERROR DURING AUTOMATIC ULTRASONIC INSPECTION OF POLYMER COMPOSITE PRODUCTS Improving of the product quality without corresponding development of methods and means of nondestructive testing and diagnostics under modern conditions is not practically possible. It is especially topical for polymer composite products having a number of ad- vantages over traditional materials such as metals, particularly, in aerospace brunches of engineering. From the point of view of increasing the validity of results of product nondestructive testing and the rate of its performance, the automatic nondestructive testing systems are the most prospective. When performing the automatic testing, the matter of an accuracy of determining areas of defects to be detected is one of the most topical. The paper considers matters of the accuracy of determining the defect areas during contactless ultrasonic automatic nondestructive testing of cylindrical polymer composite products that was conducted in accordance with the type procedure at CRISM JSC. The theoretical calculation of the dependence of relative error of determining areas of defects on their area for different values of scanning parameters has been performed. There are presented results of experimental studies that qualitatively confirm theoretical proposi- tions. The quantitative estimation of the total defect area error showed that the resulting value is within the limits of 20 % and depends on dimensions of defects detected during testing. Keywords: contactless ultrasonic inspection, scanning error, defect area. Статья поступила в редакцию 16.08.2017 Received 16.08.2017