1 PERANCANGAN SISTEM INTERLOCK PMT DAN PMS MENGGUNAKAN PROGRAMMABLE LOGIC CONTROL (PLC) BERBASIS SUPERVISORY CONTROL AND DATA ACQUISITION (SCADA) Nur Hidayat Arief. 1 , Ir. Yuningtyastuti, M.T. 2 Karnoto, S.T., M.T. 3 Jurusan Teknik Elektro, Fakultas Teknik, Universitas Diponegoro Jl. Prof. Sudharto, Tembalang, Semarang, Indonesia Email :nuharief@gmail.com ABSTRAK SCADA (Supervisory Control And Data Acquisition) memiliki fungsi sebagai telemetring, telecontrol, dan teleindication. Sehingga sistem SCADA diperlukan sebagai pengendalian sistem tenaga listrik, pengawasan kontrol dan pengambilan data dari jarak jauh, mulai dari pengambilan data pada peralatan pembangkit atau Gardu Induk, pengolahan informasi yang diterima, sampai reaksi yang ditimbulkan dari hasil pengolahan informasi. Dengan adanya sistem SCADA penyampaian dan pemrosesan data dari sistem tenaga listrik akan lebih cepat diketahui oleh operator (dispatcher). Informasi pengukuran dan status indikasi dari sistem tenaga listrik dikumpulkan dengan menggunakan peralatan yang ditempatkan di Gardu Induk (GI) dan di pusat pembangkit. Tujuan tugas akhir ini adalah untuk merancang sistem SCADA (Supervisory Control and Data Acquisition) pada plant sistem interlock PMT dan PMS menggunakan perangkat lunak Wonderware Intouch sebagai tampilan HMI, PLC berperan sebagai RTU, mikrokontroller Atmega32 berperan sebagai program akusisi data besaran listrik, dan laptop berperan sebagai MTU. Dimana komunikasi data yang digunakan adalah komunikasi serial dengan kabel RS485 pada PLC dan komunikasi data serial yang dimiliki oleh mikrokontroller Atmega32 dengan media USART (Universal Synchronous and Asynchoronous Serial Transmitter) yang diterima pada program penerimaan data serial ke MS Excel. Sehingga semua data yang dikirim oleh PLC dan mikrokontroller Atmega32 dapat terbaca oleh program HMI SCADA Wonderware Intouch. Dari hasil penelitian didapatkan bahwa program akuisisi data besaran listrik dapat menampilkan dan mengirimkan data besaran listrik berupa tegangan, arus dan frekuensi secara realtime pada plant dan ditampilkan juga pada HMI. Plant sistem tenaga listrik operasi manuver gardu induk dapat diawasi dan dikendalikan melalui masukan dan keluaran pada plant, antarmuka pada laptop. Untuk prosedur manuver Gardu Induk dapat dilakukan melalui HMI laptop, dengan sistem interlock antara PMT (CB) dengan PMS (DS) untuk mencegah terjadinya kegagalan dalam prosedur manuver. Pada plant dapat disambungkan dengan rele proteksi untuk simulasi gangguan yang terjadi. Apabila terjadi simulasi gangguan maka akan muncul peringatan pada HMI, alarm akan bekerja dan indikator PMT (CB) tertentu akan off. Kata kunci : SCADA, Gardu Induk, PLC, mikrokontroller Atmega32, PMT, PMS ABSTRACT SCADA (Supervisory Control and Data Acquisition) has functions as telemetring, telecontrol, and teleindication. Therefore, SCADA system is required as the electric power system control, control supervisory and data acquisition from long distance, from the recording of the generator or substation equipment, information processing received, until the reaction generated from the result of information processing. With the SCADA system, delivery and processing of data from the power system will be immediately visible to the operator (dispatcher). Measurement information and indicative status of the power system are collected by using equipment placed in the substation (GI) and in the generator. The purpose of this thesis is to design a SCADA system (Supervisory Control and Data Acquisition) in the CB and DS interlock plant system using Wonderware Intouch software as view of HMI, PLC which is had roles as RTU, Atmega 32 microcontroller as electrical quantities data acquisition program, and laptop as MTU. Data communication used are serial communication with RS485 cable in the PLC and serial data communication owned by the ATmega32 microcontroller with USART (Universal Synchronous and Asynchoronous Serial Transmitter) media received in serial data acquisition program into MS Excel. Therefore, all the data sent by PLC and the Atmega32 microcontroller can be read by HMI SCADA Wonderware Intouch. The result showed that the amount of electricity data acquisition program can display and transmit the data of electrical quantities such as voltage, electric current and frequency in real time on the plant and also be displayed on the HMI. The power plant system of operation maneuver substation can be monitored and controlled via the input and output of the plant, the interface on the laptop. To the maneuver procedure of substation can be done through the substation HMI laptop, with the interlock system between the PMT (CB) with PMS (DS) to prevent failure in maneuvering procedures. At the plant can be connected with the protection relay for disturbance simulation. If there is a disturbance, HMI will display a warning, the alarm will work and a certain indicators PMT (CB) will be off. Keyword : SCADA, Substation, PLC, microcontroller Atmega32, CB, DS 1 Mahasiswa Jurusan Teknik Elektro Universitas Diponegoro 2,3 Dosen Jurusan Teknik Elektro Universitas Diponegoro