308 Pengaruh Waktu dan Tegangan Listrik terhadap Kadar COD dan Fosfat pada Limbah Cair Nata De Coco Dengan Metode Hibridisasi Pipe Filter Layer-Elektrolisis (HPFLE) Diky Ihsan Pratama* 1 , Ryan Bima Aditya 2 , Siti Fatimah 3 1,2,3 Program Studi Teknik Kimia, Universitas Muhammadiyah Surakarta Email: *1 dikyihsan@yahoo.com, Bimaadityaryan@gmail.com, Sf120@ums.ac.id Submitted :22-01-2020 Accepted :18-04-2020 Available online :14-05-2020 ABSTRAK Penelitian ini dilakukan untuk megetahui efek dari metode HPFLE (hibridisasi pipe filter layer- elektrolisis) terhadap limbah hasil pengolahan nata de coco karena limbah cair dari hasil pengolahan nata de coco belum terlalu menjadi perhatian dari pemilik industri sehingga mencemari ekosistem air. Dalam penelitian ini digunakan 2 variabel bebas yaitu variasi absorben pada pipe filter layer serta variasi tegangan dan waktu perlakuan untuk tahapan elektrolisis. Absorban yang digunakan berupa sabut kelapa, zeolit, pasir, kain, dan spon. Variasi tegangan yang digunakan adalah 5 volt, 10 volt, dan 15 volt sedangkan variasi waktunya adalah 10 menit, 30 menit, 45 menit, 60 menit, dan 75 menit. Dari variabel-variabel yang ada diketahui bahwa pada tahapan pipe filter layer memberikan efek terhadap kadar COD sebesar 13, 14% sedangkan untuk fosfat 9,7%. Untuk tegangan elektrolisis pada kadar COD yang memiliki efektifitas terbaik pada 5 volt dengan waktu perlakuan 75 menit. Sedangkan untuk fosfat tegangan yang efektif yaitu pada 5 volt dengan waktu 10 menit. Dari penelitian ini diketahui metode HPFLE memberikan pengaruh hingga kadar COD menjadi 4000 mg/L sedangkan untuk fosfat menjadi 179,01 mg/L. Kata Kunci: elektrolisis, pipe filter layer, COD, fosfat ABSTRACT This research is conducting to determine effect of HPFLE (hibridisasi pipe filter layer-elektrolisis) method on the waste produced by nata de coco because the waste hs not been too much of a concern of the industrial owner, so that it pollutes the water ecosystem. In this research used two independent variables that is variations in absorbance in the pipe filter layer and variations in voltage and treatment time for the electrolysis stage. Absorbants used in the form of kelaa coir, zeolite, sand, cloth, and sponges. The voltage variations used are 5 volts, 10 volts, and 15 volts while the time variations are 10 minutes, 30 minutes, 45 minutes, 60 minutes, and 75 minutes. From the existing variables, it is known that at the pipe filter layer stage the content of COD gives an effect of 13, 14% while for 9.7% of phosphate. For electrolysis voltage at the COD level which has the best effectiveness at 5 volts with 75 minutes treatment time. As for phosphate, the effective stress is at 5 volts within 10 minutes. Fr om this research, it’s known that HPFLE method gives effect to COD level to 4000 mg/L while for phosphate to 179,01 mg/L Keywords: electrolysis, pipe filter layer, COD, phosphate E-ISSN-2580-7129 Print- ISSN-1978-6107 TECHNO: JURNAL PENELITIAN Journal homepage: http://ejournal.unkhair.ac.id/index.php/Techno Issue 09 Number 01 May 2020 DOI: http://dx.doi.org/10.33387/tjp.v9i1.1551