Dinamika : Jurnal Ilmiah Teknik Mesin 35 p-ISSN: 2085-8817 e-ISSN: 2502-3373 Vol. 12, No. 1, November 2020 DOI: 10.33772/djitm.v12i1.12894 PERANCANGAN HRSG (HEAT RECOVERY STEAM GENERATOR) SEBAGAI PEMANAS REFRIGRANT R-134a PADA SIKLUS ORGANIC RANKINE CYCLE D.L Zariatin 1 , I.G.E Lesmana 2 , R.C Hartantrie 3 , A Nugroho 3 1, 2, 3, 4 Teknik Mesin, Universitas Pancasila 1 dedeliazariatin@univpancasila.ac.id 2 gdlesmana@univpancasila.ac.id 3 rovida.camalia@univpancasila.ac.id 4 adityanugroho820@gmail.com ABSTRAK Udara buang proses pirolisis masih menyimpan energi panas yang cukup tinggi dengan temperature mencapai 800°C sehingga dapat dimanfaatkan sebagai media untuk merubah fase Refrigerant R-134a dari fase cair menjadi gas. Refrigerant R-134a yang sudah berubah menjadi gas digunakan untuk memutar turbin sebagai penggerak generator sehingga dapat menghasilkan aliran listrik dalam siklus Organic Rankine Cycle (ORC). Refrigrant R-134a tidak menyerap panas dari proses pirolisis secara langsung. Panas dari pirolisis diserap melalui siklus thermal oil kemudian digunakan untuk mengubah fasa R-134a pada Heat Recovery Steam Generator (HRSG). Desain HRSG pada penelitian ini adalah tipe sistem heat exchanger shell and tube. Dimana thermal oil yang memiliki suhu panas mengalir dalam shell dan Refrigerant R-134a yang memiliki suhu dingin mengalir dalam tube. Pertukaran panas terjadi ketika Refrigerant R-134a masuk ke dalam tube dan thermal oil masuk ke dalam shell. Dalam perancangan HRSG ini digunakan tiga variasi tekanan yaitu 8 bar, 10 bar, dan 12 bar. Data suhu, tekanan, diameter tube, dan mass flow rate di- input pada software HTRI Xchanger suite kemudian diproses oleh software tersebut sehingga menghasilkan output berupa laju perpindahan panas. Nilai laju perpindahan panas berturut turut sebesar 2,084 kJ/s, 2,622 kJ/s, dan 3,02kJ/s. Sehingga dapat disimpulkan hasil yang paling optimal berada pada tekanan 12 bar dengan nilai laju perpindahan panas sebesar 3,02 kJ/s Kata kunci: shell and tube HRSG, HTRI Xchanger suite, Organic Rankine Cycle ABSTRACT Design of Heat Recovery Steam Generator (HRSG) as a heater of Refrigrant R134-a on Organic Rankine Cycle. The exhaust gas from the pyrolysis process stores enough thermal energy with temperature up to 800°C, it can be used to convert the refrigerant phase R-134a from the liquid phase to gas. Refrigerant R-134a, which is turned into a gas, is used to set the turbine as a generator drive so that it can generate electricity in the Organic Rankine Cycle (ORC) cycle. Refrigerant R-134a does not absorb heat from the pyrolysis process directly. The heat from pyrolysis is absorbed through the thermal oil cycle then used to change the R-134a base in the Heat Recovery Steam Generator (HRSG). The HRSG design in this study is a type of shell and tube heat exchanger system. Where thermal oil has hot temperature flows in the shell, and refrigerant R-134a, which has cold temperature flows in the tube. Heat exchange occurs when refrigerant R-134a enters the tubes, and thermal oil enters the shell. In designing this HRSG, three pressure variations were used, namely 8 bars, 10 bars, and 12 bars. Data on temperature, pressure, tube diameter, and mass flow rate are input in the HTRI Xchanger suite software and then processed by the software to produce an output in the form of heat transfer rate. The values of heat transfer rates were 2.084 kJ / s, 2.622 kJ /s, and 3.02 kJ / s, respectively. So that it can be concluded that the most optimal results are at 12 bar pressure with a heat transfer rate of 3.02 kJ / s Keywords: shell and tube HRSG, HTRI Xchanger suite, Organic Rankine Cycle