Volume 4 • Issue 1 • 1000137 J Civil Environ Eng ISSN: 2165-784X JCEE, an open access journal Moses, J Civil Environ Eng 2014, 4:1 DOI: 10.4172/2165-784X.1000137 Research Article Open Access Investigation of Performance of Glass Fibre Impregnated with Bitumen Emulsion against Reflective Cracking Ogundipe Olumide Moses* Civil Engineering Department, Ekiti State University, Ado-Ekiti, Nigeria Abstract The study investigates the use of glass fbre impregnated with bitumen emulsion with 6mm aggregates compacted on it as a Stress Absorbing Membrane Interlayer (SAMI) to retard refective cracking. The causes and mechanism of refective cracking in an overlay over a cracked pavement were highlighted. Tests were carried out in a wheel tracking facility to induce modes I and II cracking. The effects of temperature, load level, composition of SAMI and overlay thickness on the performance of the SAMIs were evaluated. It was found that the two SAMIs investigated in this study were both able to retard refective cracking. Better relative performance was observed with low overlay thickness and at high load level. Also, the study showed that temperature infuenced the performance of the SAMIs and indicated that difference in the viscosity of the bitumen emulsion used in the SAMIs led to difference in performance. It was observed that the interface shear strain of the overlay-SAMI interface infuenced the performance of the SAMI. *Corresponding author: Ogundipe Olumide Moses, Civil Engineering Department, Ekiti State University, Ado-Ekiti, Nigeria, Tel: +2348107825001; E mail: momide2002@yahoo.com Received November 11, 2013; Accepted January 21, 2014; Published January 30, 2014 Citation: Moses OO (2014) Investigation of Performance of Glass Fibre Impregnated with Bitumen Emulsion against Refective Cracking. J Civil Environ Eng 4: 137. doi:10.4172/2165-784X.1000137 Copyright: © 2014 Moses OO. This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited. Keywords: Cracks; Overlay; Interlayer; Temperature; Load level Introduction Te method commonly used to rehabilitate deteriorated pavements is by overlaying with a new surfacing material. Cleveland et al. [1] stated that for both fexible and composite pavements, a common technique used by many agencies for preventive maintenance and/or rehabilitation was simply to construct thin Hot Mix Asphalt (HMA) overlay, normally between 25 and 50 mm thick. Overlaying cracked pavements prevents water from infltrating through the cracks into the pavement structure, thus preventing the deterioration of the pavement structure and increasing its structural capacity. Also, it reduces roughness, restores skid resistance, and improves the overall ride quality to the travelling public. However, it has been found that the cracks propagate through the overlay to its surface, a phenomenon called refective cracking. Refective cracking can be defned simply as the propagation of existing cracks in an old pavement through the underside of the overlay to the surface. (Figure 1) shows a schematic of refective cracking in HMA overlay on Portland Cement Concrete (PCC) slab or Asphalt Concrete (AC). Refective cracking is ofen initiated at the bottom of the overlay material and grows until it appears at the surface. Also top-down cracking (cracks initiating at the surface and growing into the lower layers) occurs especially where there are large temperature variations in the pavement (thermal cracking). A number of factors have been identifed as the causes of refective cracking. Palacios et al. [2] reported that cracks propagate to new overlays due to vertical movement of the underlying pavement layer which may be due to trafc loading, frost heave and consolidation of the sub grade soils and/or the horizontal movement of the pavement upper layers due to temperature changes. Quintus et al. [3] reported three causes of refective cracking, the major being horizontal movements from the expansion and contraction of the base pavement that is caused by temperature changes; the diferential vertical defections between the approach and departure slabs or across transverse cracks, which create shear stresses; and the curling of PCC slabs during colder temperature when the HMA overlay is stif and brittle. Abe et al. [4] stated that cracking was caused on the surface of the overlay at an early stage by the movement of the pavement and trafc load. Smith [5] also mentioned the diferential vertical movement at a crack or slab joint in the old pavement which induces a vertical shear stress in the overlay, horizontal movement associated with temperature or moisture changes in the old pavement which induces tensile stress in the overlay or live load fexural stress in the overlay, which tends to concentrate directly over discontinuities. Based on the causes identifed by researchers, there seems to be an agreement on the causes of refective cracking. While it is common knowledge that factors such as sub grade conditions, pavement material quality, workmanship etc afect the performance of a pavement; the principal factors responsible for refective cracking are the action of trafc loading on an overlay on a cracked pavement and thermal stresses developed as a result of daily/seasonal temperature variation. Tis study has concentrated on refective cracking caused by the action of trafc loading. It is important that the mechanisms of refective cracking are well understood to be able to provide a solution to the problem. Tis is illustrated in Figures 2 and 3. Figure 2a depicts a situation where the moving wheel on the edge of the pavement above the crack produces maximum shear stresses, A and C respectively as shown in Figure 3, while in Figure 2b, the wheel directly on the overlay above the cracked pavement generates fexural stresses producing maximum bending stress, B as indicated in Figure 3. Tis illustration indicates two of the three modes of refective cracking - Modes I and II. Molenaar [6] Overlay PCC/AC (Existng surface) Subbase Crack/joint Reflective cracking Subgrade Wheel load Figure 1: Schematic of refective cracking in pavement. J o u r n a l o f C i v il & E n v i r o n m e n t a l E n g i n e e r i n g ISSN: 2165-784X Journal of Civil & Environmental Engineering