Copyright 2002, Society of Petroleum Engineers Inc. This paper was prepared for presentation at the SPE International Petroleum Conference and Exhibition in Mexico held in Villahermosa, Mexico, 10–12 February 2002. This paper was selected for presentation by an SPE Program Committee following review of information contained in an abstract submitted by the author(s). Contents of the paper, as presented, have not been reviewed by the Society of Petroleum Engineers and are subject to correction by the author(s). The material, as presented, does not necessarily reflect any position of the Society of Petroleum Engineers, its officers, or members. Papers presented at SPE meetings are subject to publication review by Editorial Committees of the Society of Petroleum Engineers. Electronic reproduction, distribution, or storage of any part of this paper for commercial purposes without the written consent of the Society of Petroleum Engineers is prohibited. Permission to reproduce in print is restricted to an abstract of not more than 300 words; illustrations may not be copied. The abstract must contain conspicuous acknowledgment of where and by whom the paper was presented. Write Librarian, SPE, P.O. Box 833836, Richardson, TX 75083-3836, U.S.A., fax 01-972-952-9435. Abstract We present results of modeling studies of injection schemes with wells using new completions technology, and address how these are applied or envisaged for the fulfillment of field development strategies in offshore environments. Introduction A common theme in offshore developments is the use of fewer wells to achieve the production targets of the field. In mature fields, the limited availability of well slots is a severe constraint. In new developments, the drive is towards fewer and smaller platform installations. In subsea developments, particularly in deepwater, the objective is minimization of wellheads. There are clear financial, environmental, and technical reasons for these trends. The use of advanced completions technology to reduce well requirements has been widely practiced in relation to production wells. Commingling of production in layered, compartmentalized, and dispersed geological settings has been achieved with multilateral wells, and conventional wells with flow control technology. 1-4 The application of this technology to injection problems has received relatively little attention. 5-6 The objective of this study is to analyze a number of injection problems that arise from actual field development scenarios. Four cases will be presented. The first two concern achieving proper partitioning of injected water into multi-zone structures. The third case concerns achieving the total target injection rate and partitioning. The fourth case concerns the alternating injection of water and gas. Two-Zone Injection This is a deepwater field, being developed by subsea wells. The structure consists of two partially overlapping formations of high permeability (3-5 Darcies), separated by non-reservoir rock. There is no external drive mechanism in the reservoir (e.g. an aquifer). Injection is to commence at initial production. Vertical injectors completed in both formations are to be used. The lower formation has about 1.5 times the injectivity of the upper formation because of its larger effective thickness. The objective is to inject into the upper and lower formations with a split of about 45% and 55% respectively, in line with the estimated distribution of reserves. The operator plans to install fixed and/or variable flow control devices in the injectors. The study analyzed injection options with and without valves. As Figure 1 shows, when no valves are used, the water will spontaneously partition between the two zones in the ratio of about 20% into the upper zone and 80% into the lower zone at relatively low injection rates. As the injection rate increases, so does the frictional pressure loss and this changes the ratio between the upper and lower zones to about 35% and 65%. This is shown in Figure 2. Note, however, that the fracture gradient of the formation imposes a constraint on the injection rate. Figure 3 shows that the desired partitioning can be achieved when both formations are equipped with variable flow control valves. By adjusting the valve apertures, the partitioning of the injectivity can be adjusted as reservoir conditions evolve. Three-Zone Injection This example concerns injection into three zones simultaneously, prompted by the limited number of well slots available on the platform from which this reservoir is being developed. In comparison to the previous example, there is greater contrast in the reservoir properties among the three zones, so that the middle zone has the highest injectivity index. The operator has initiated a water injection program for pressure maintenance, using vertical dual-string injection wells (two " 3 2 1 tubing strings), with the short string injecting into Zone A and the long string into Zones B and C. With this configuration, the approximate partitioning in injectivity is 25%, 50%, and 25% (Figure 4). SPE 74392 Advanced Completions for Injection Applications Allyson Gajraj, SPE, Schlumberger; Chuanping He, SPE, Stanford University; Soraya Betancourt, SPE, Schlumberger; Ruijian Li, SPE, Schlumberger; and Younes Jalali, SPE, Schlumberger