JURNAL REKAYASA KONSTRUKSI MEKANIKA SIPIL (JRKMS) Volume 04 Nomor 02 September 2021 p-ISSN 2614-5707 e-ISSN 2715-1581 Fakultas Teknik Universitas Katolik Santo Thomas ejournal.ust.ac.id/index.php/JRKMS | 91 Pengujian Peningkatan Kapasitas Lentur dengan Penambahan Dimensi pada Sisi Bawah dan Atas Balok Beton Bertulang Samsuardi BATUBARA 1* , Martius GINTING 1 , Francois SIREGAR 1 1 Program Studi Teknik Sipil, Universitas Katolik Santo Thomas, email: samsuardi_btbr@yahoo.com Sejarah artikel Diserahkan: Dalam bentuk revisi: 23 Agustus 2021 23 September 2021 Diterima: Tersedia online: 28 September 2021 30 September 2021 Abstract This research aims to test the flexural capacity increase of a reinforced concrete beam after increasing the dimensions of the beam on the bottom and top sides. We used 3 specimens of reinforced concrete beams with a dimension of 150 mm x 200 mm, span of 3000 mm. The first specimen was unreinforced, the second was reinforced by adding dimensions to the bottom side, and the third was reinforced by adding dimensions to the top side. With the addition of dimensions of 150 mm x 100 mm with a span of 3000 mm, the dimensions of the reinforcement test specimen become 150 mm x 300 mm with a span of 3000 mm. For the unreinforced specimen, the load was applied with a hydraulic jack in the middle of the span and was loaded until the test specimen fails. Meanwhile, for the reinforced test specimen, the load was applied in two stages. The test results show that for the specimen with the addition of dimensions on the bottom side of the reinforced concrete beam, the flexural capacity increased by 211.84%. Meanwhile, for the specimen with the addition of dimensions on the upper side, the flexural capacity increased by 192,98% against the specimen without reinforcement. Based on the increase in flexure, it can be concluded that the addition of dimensions on the bottom side of the beam and on the bottom side of the reinforced concrete beam is safe to do. Keywords: reinforced concrete beams, flexural capacity, reinforcement, beam dimensions Abstrak Pengujian ini bertujuan untuk mengetahui besar peningkatan kapasitas lentur pada balok beton bertulang yang diperkuat dengan menambah dimensi balok pada sisi bawah dan sisi atasnya. Kami menggunakan 3 buah benda uji balok beton bertulang dengan dimensi 150 mm x 200 mm bentang 3000 mm. Benda uji pertama adalah tanpa perkuatan, yang kedua adalah diperkuat dengan menambah dimensi pada sisi bawah, dan yang ketiga adalah diperkuat dengan menambah dimensi pada sisi atas. Dengan penambahan dimensi sebesar 150 mm x 100 mm bentang 3000 mm, dimensi benda uji perkuatan menjadi 150 mm x 300 mm bentang 3000 mm. Pemberian beban untuk benda uji tanpa perkuatan dilakukan dengan jack hidraulic pada tengah bentang dan dibebani hingga benda uji runtuh. Sementara, untuk benda uji dengan perkuatan pemberian beban dilakukan dengan dua tahap. Hasil pengujian menunjukkan bahwa untuk benda uji dengan penambahan dimensi pada sisi bawah balok beton bertulang, kapasitas lentur meningkat sebesar 211,84 %. Sedangkan, untuk benda uji dengan penambahan dimensi pada sisi atas kapasitas lentur meningkat sebesar 192,98 % terhadap benda uji tanpa perkuatan. Berdasarkan peningkatan lentur tersebut dapat disimpulkan bahwa penambahan dimensi pada sisi bawah balok maupun pada sisi bawah balok beton bertulang aman untuk dilakukan. Kata kunci: balok beton bertulang, kapasitas lentur, perkuatan, dimensi balok