STUDI PENENTUAN KONFIGURASI SISTEM INDUKSI PADA INDUCED CURRENT ELECTRICAL IMPEDANCE TOMOGRAPHY (ICEIT) Yustitia Putri Indraswari 1 , Dudi Darmawan 2 , Mamat Rokhmat 3 1,2,3 Prodi S1 Teknik Fisika, Fakultas Teknik, Universitas Telkom 1 yustitia92@gmail.com, 2 dudiddw@gmail.com, 3 mamatrokhmat76@gmail.com Abstrak Salah satu cara untuk mengatasi masalah sensitivitas perubahan konduktivitas objek ( distinguishability) yang jauh dari batas adalah dengan pemberian arus melalui penginduksian medan magnet. Cara tersebut biasa disebut induced current electrical impedance tomography (ICEIT). Cara ini diharapkan dapat memberikan distribusi arus induksi yang lebih merata dan menjangkau seluruh permukaan objek. Distribusi arus induksi yang terjadi pada permukaan objek ditentukan oleh distribusi medan magnet. Sehingga, diperlukan pemberian distribusi medan magnet yang homogen. Pemberian distribusi medan magnet homogen ini diprediksi bisa menghasilkan distribusi arus induksi yang lebih representatif menutup seluruh permukaan objek. Oleh karena itu dibutuhkan konfigurasi koil yang tepat agar dapat meningkatkan kemampuan deteksi anomali dan distinguishability agar dihasilkan citra rekonstruksi yang baik. Pada penelitian ini, konfigurasi koil penginduksi diperoleh melalui penentuan jumlah induksi dan posisi setiap induksi yang optimal dan objek yang digunakan berbentuk rectangular dengan bentuk koil yang sama. Dari hasil simulasi dengan variasi jumlah induksi diperoleh bahwa distribusi medan magnet semakin homogen jika memberikan jumlah induksi lebih banyak pada objek. Variasi posisi induksi pada suatu konfigurasi koil tertentu akan menentukan kehomogenan distribusi medan magnet. Kata Kunci : induced current electrical impedance tomography, konfigurasi koil, rectangular coil, kehomogenan medan magnet Abstract One way to overcome the problem of the sensitivity of the object conductivity changes (distinguishability) which far from the boundary is the provision of current through the induction of the magnetic field. This way called induced current electrical impedance tomography (ICEIT). This method is expected to give the induced current distribution more equitable and reach the entire surface of the object. The distribution of the induced current in the surface of the object is determined by the distribution of the magnetic field. Thus, the necessary provision of a homogeneous magnetic field distribution. Giving this a homogeneous magnetic field distribution is predicted to generate the induced current distribution more representative cover the entire surface of the object. Therefore, the proper coil configuration is required to improve the ability of anomaly detection and distinguishability in order to produce a good image reconstruction. In this research, coil configuration is obtained by determining the number and position of each optimal induction and used rectangular shaped object with the same coil shape. From the simulation results obtained by varying the amount of induction that the more homogeneous distribution of the magnetic if it gives the number of induction more on the object. Variations induction position on a particular coil configuration will determine the distribution of magnetic field homogeneity. Keywords : induced current electrical impedance tomography, coil configuration, rectangular coil, homogeneity of the magnetic field 1. Pendahuluan Electrical Impedance Tomography merupakan tomografi yang berdasarkan karakteristik listrik objek. Terdapat dua metoda dalam EIT dalam menentukan distribusi resistivitas objek yaitu dengan cara injeksi arus (ACEIT) atau dengan induksi arus (ICEIT). Masalah sensitivitas terhadap perubahan konduktivitas objek (distinguishability) yang jauh dari batas yang terjadi pada sistem injeksi arus dapat diatasi salah satunya dengan cara sistem induksi arus (ICEIT). Teknik pemberian arus dapat menentukan kerapatan arus yang terbentuk pada objek dan dapat mempengaruhi hasil rekontruksi gambar [1].Pemberian arus melalui penginduksian medan magnet pada ICEIT dapat dilakukan di seluruh permukaan objek melalui konfigurasi koil tertentu. Pola arus ini dihasilkan melalui penginduksian medan magnet melalui konfigurasi koil tertentu [2]. Pola arus juga akan mempengaruhi distribusi medan magnet yang menginduksi objek. Diperlukan pemberian medan magnet yang homogen pada daerah ISSN : 2355-9365 e-Proceeding of Engineering : Vol.2, No.1 April 2015 | Page 531 brought to you by CORE View metadata, citation and similar papers at core.ac.uk provided by Open Library